Close-up of gloved hands servicing the ice maker mechanism inside an open freezer door

No ice, small cubes, leaks and jammed ejectors

Ice Maker Repair Oak Ridge TN

An ice maker that stops dropping cubes is usually a failed water inlet valve, a frozen fill tube, or a clogged filter, not a dead ice maker. We repair ice makers across Oak Ridge, TN, find the failed part on site, and quote an upfront price before any work begins. Call (865) 324-1626, Mon-Fri 8AM-6PM.

Upfront pricingWater faults tracedTested before we leave
Call firstDescribe the symptom and we will triage it
Water leaking?Shut the supply valve and call before it spreads
Diagnose the causeWe test the failed part, not guess at it
Approve the repairPrice agreed before work starts

What's included

What Our Ice Maker Repair Covers

An ice maker is a small water appliance living inside your freezer. Every call gets the full water path checked, from the wall valve to the ice bin.

01

Water supply diagnosis

Inlet valve, fill tube, supply line and shutoff valve. Most no-ice complaints start here.

02

Freeze and harvest cycle

Ice mold thermostat, ejector arm and mold heater. We confirm the full cycle runs.

03

Leaks and overflows

Fill tube alignment, water level and mold condition. We stop the drip at its source.

04

Filter and water quality

Clogged filters, hard-water scale and small hollow cubes. We restore full, clean flow.

Service overview

Ice Maker Repair That Finds the Real Fault

An ice maker fills a mold, freezes it, then harvests the cubes on a timer. When the bin stays empty, the water never arrived or the harvest never triggered, and the fix is the failed step.

The call we get most is the ice maker that quit after a filter change or a few months of slow decline. The usual story: a saddle valve or inlet valve scaled half-shut by hard water, so the mold fills weakly and drops small hollow cubes, or nothing at all. The other classic is a frozen fill tube, where water dribbles, freezes in the tube, and blocks the next fill. Thawing the tube without fixing the dribble just repeats the cycle.

Our Oak Ridge appliance repair team runs ice maker calls from West Hills to Emory Valley. If water is leaking behind the fridge, shut the supply valve and call before it reaches the floor. The ENERGY STAR refrigerator guidance covers efficient operation once everything is working again.

Cubes dropping againWe confirm a full harvest cycle and steady water fill, not just that the arm moves.
Leaks traced to sourceFill tubes, valves and supply lines all get checked so the puddle does not come back.
Repair before replaceMost ice maker repairs run $150-$400. We show you the honest math when replacement is smarter.
Close-up of hands probing an electronic control board with a multimeter
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.

The service timeline

How an Ice Maker Repair Visit Goes

The process flexes to the condition, but these checkpoints keep decisions clear.

01

Symptom and water check

We check the supply valve, water pressure, and whether the mold is filling at all.

Stage 1
02

Fill tube and valve inspection

The fill tube gets checked for ice blockage and the inlet valve gets tested electrically. Most failures end here.

Stage 2
03

Upfront price

You get the diagnosis, the part cost and the labor in one number. If the mold assembly plus valve costs more than the unit is worth, we say so.

Stage 3
04

Repair and fit

We fit the failed part, clear the fill tube, replace the filter if it is due, and check the ejector and thermostat. Most ice maker repairs finish in one to two hours.

Stage 4
05

Harvest verification

We run the cycle and confirm cubes are forming, harvesting and dropping into the bin before we call it done.

Stage 5

Tools & methods

The Tools Behind a Proper Ice Maker Fix

Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.

01

Multimeter

Tests the inlet valve solenoids, mold thermostat and ejector motor for the exact failure point.

02

Water pressure gauge

Confirms the supply delivers enough pressure to fill the mold properly.

03

Thaw and clear tools

Safely clears a frozen fill tube without damaging the line.

04

Model-matched parts

Inlet valves, ice maker assemblies, filters and supply lines sourced for your make and model.

Use cases

Ice Maker Problems We See Most in Oak Ridge

Typical calls from local kitchens and laundry rooms, and what the fix usually looks like.

Technician repairing a motor assembly on a workshop bench
The no-ice callBin empty for weeks. The classic failed inlet valve or frozen fill tube. After the fix, the mold fills fully and cubes drop on schedule.

Small, hollow, or shell-like cubes

Weak water fill from a scaled valve or low pressure. We restore full flow and the cubes come out solid again.

Water leaking behind the fridge

A fill tube spraying outside the mold or a valve that will not shut. We realign or replace the failed part and check the floor for damage.

Problems we solve

Common Ice Maker Symptoms and Causes

Match what your ice maker is doing to the likely cause. For the fridge it lives in, see our refrigerator repair page. Freezer trouble too? Our freezer repair page covers that.

ISSUE

No ice at all

Failed inlet valve, frozen fill tube, or the ice maker switched off. We check the simple causes first.

SYMPTOM

Small or hollow cubes

Weak water fill from scale or low pressure. We restore flow and verify cube quality.

SIGN

Leaking water

Misaligned fill tube or a valve stuck open. We trace it to the source.

SituationUsually repairConsider replacing
Ice maker under 8 years oldValve, fill tube, thermostatMold cracked and valve failed together
Repair quote under half of newMost single-part failuresFull assembly plus water damage
Standalone ice makerValve, pump, thermostat faultsCompressor failure on an old unit

Pricing process

Ice Maker Repair Pricing in Oak Ridge

$150 - $400 depending on scope

Phase 01

Part needed

Inlet valves, thermostats and filters are modest parts. Full ice maker assemblies cost more, and we explain why before you decide.

Phase 02

Water damage found

A slow leak behind the fridge can damage flooring before anyone notices. If we find damage beyond the appliance, we flag it before quoting.

Phase 03

Fridge vs standalone

Built-in fridge ice makers are quick to reach. Standalone undercounter units take longer to pull and service. You approve the final number before we start.

Booking with us

What to Expect When You Book

One call, one visit in most cases, and a price you approve before any work starts.

01

Call or request online

Tell us the brand, the model if you can read it off the plate, and exactly what the appliance is doing. A few triage questions on the phone sometimes settle simple issues without a visit.

02

Diagnosis with an upfront price

On site we test the appliance and trace the fault to its cause. You get the repair options and the full price before any work starts, so there are no surprises after.

03

Repair with quality parts

We fit quality replacement parts suited to your model and finish the repair in the same visit whenever the part is on hand.

04

Testing and care tips

We run the appliance through its paces, confirm it is operating safely, and leave you with simple care tips so the fix lasts.

[ADD VERIFIED CUSTOMER REVIEW HERE]

Questions before we arrive

Frequently Asked Questions

Hands testing an electronic control board with meter probes
Call (865) 324-1626
How much does ice maker repair cost in Oak Ridge?

Most ice maker repairs in Oak Ridge run $150 to $400. Inlet valves, thermostats and filters sit at the lower end, while full ice maker assemblies cost more. We diagnose first and give you the full price before any work starts.

Why did my ice maker suddenly stop making ice?

Check that the ice maker is switched on and the bin is seated properly, since a raised shutoff arm pauses production. Past that, the usual causes are a failed water inlet valve, a frozen fill tube, or a clogged water filter. If the freezer itself is not holding 0 degrees, fix the cooling problem first.

Why are my ice cubes small and hollow?

Small hollow cubes mean the mold is not filling fully. Hard-water scale in the inlet valve or low supply pressure are the usual causes in Oak Ridge homes. Replacing the filter helps only if the filter is actually clogged; a scaled valve needs replacing.

Can I fix a frozen fill tube myself?

You can thaw it with a hair dryer on low heat, keeping the heat moving so nothing melts or cracks. But a fill tube usually freezes because water is dribbling from a valve that does not shut fully, so it will freeze again. We fix the dribble, not just the ice.

Should I repair my ice maker or replace it?

A built-in ice maker under about 8 years old is usually worth repairing, since most failures are affordable parts. Replacement makes more sense when the mold is cracked and the valve has failed together, or repair costs pass half the price of a new assembly. The table above lays out the decision the way we explain it on site.

Ready when you are

No Ice in the Bin? Get Ice Maker Repair in Oak Ridge

Call (865) 324-1626 Mon-Fri, 8AM-6PM. Most ice maker repairs run $150-$400 with the price agreed upfront, so you know the number before we start.

Technician soldering a circuit board on a workbench

Talk with the local team

Request ice maker repair

Tell us whether the ice maker is built into the fridge or a standalone unit, plus the brand and what it is doing. We answer Mon-Fri 8AM-6PM.

1980 Oak Ridge Tpke, Oak Ridge, TN 37830Dispatch office · technicians serve the full area

Thanks, your request is in. Dispatch will contact you shortly.

One call covers them all

We Service All Major Brands

GE, Samsung, Whirlpool, LG, KitchenAid, Frigidaire, Kenmore, Maytag, Bosch, Electrolux, Amana, Hotpoint, and more.

We are not a factory-authorized dealer for any brand. Have your model number handy when you call (865) 324-1626 and we will confirm we can service your unit.

See the full list of brands we service

Call dispatch